Available in lengths of 1.00 in. (25 mm), 2.00 in. (51 mm) and 3.00 in. (76 mm).
Bridgeport Fittings Copper Lay-in Lugs are for use with all grounding applications. the mounting hole accomodates 1/4 inch bolt (not included). The CLI-20 is UL and CSA Listed for Direct Burial. The CLI-20 offers excellent corrosion resistance with stainless steel set screws and high strength copper alloy construction. Wire Range CU only #4-14 AWG.
Bridgeport Fittings Copper and Aluminum Conductor Lay-in Lug for Solar Applications. The ALI-SLR is listed for use in bonding solor structures and related electrical equipment that have support frames of 1/4" width or less. The ALI-SLR offers excellent corrosion resistance with stainless steel hardware and a wireway that cuts away oxidation. Wire Range AL-Cu #4-14 AWG. 35 inch lbs. of Torque recommended.
Cap off unused PVC conduit temporarily or permanently with PVC solvent cement
Cap off unused PVC conduit temporarily or permanently with PVC solvent cement.
Clamp-on adjustable wire holder for 1 1/4 " through 3" service entrance mast, approx 1" by 15/16" wire opening.
Conduit Outlet Box
Conduit Run/Box/Fitting Hub
Connecting Elements Between Enclosures, Fittings, or Boxes Which Permit Future Changes to the System In Both Hazardous and Non-Hazardous Areas
Datacom and Low Voltage, Electrical
Designed to allow a smooth transition from cross deck ENT runs to vertical applications.
Electrical Fixing and Fastening
For 1-1/2 IN Hole
For 3 IN Hole
For 5 IN Hole
For Cable Protection Systems In a Wide Range of Industrial Applications
For Commercial and Industrial Grade
For Industrial Purpose
For Industrial, Commercial Purpose
For Masonry 3/8 - 16 X 10 inch bolt
For Model 600 Power Drive
For Physical Protection Of Cables, Pipes Or Other Cylindrical Objects.
For Sealing Off Conduit During Concrete Pours
For Use In Machine, Vehicle and Traction Building
For Use with EMT Conduit
For Use with Rigid/IMC Conduit
For Use with Rigid/IMC Conduits
For connecting portable cord to box or enclosure. Locknut not required.
For repairing broken PVC conduit a.k.a stub-ups in concrete slabs.
For use with AC/MC/MCIA in Steel or Aluminum in sizes from 14/4 to 6/3 and FMC in 3/8" trade sizes.
For use with Conduit Either Parallel With Or At Right Angle To Beams, Channels, Angles Or Columns
For use with EMT and Rigid conduit
For use with EMT and Rigid conduit or pipe
For use with EMT conduit
For use with Plenum-Gard®
For use with Rigid Conduit
For use with Riser-Gard and General Purpose
For use with non-metallic sheathed cable and flexible cord
For use with rigid/IMC conduits
For use with schedule 40 & 80 conduit
Hand held cutter makes fast square, smooth field cuts on conduit, sizes 1/2 in. through 1-1/4 in.
Hazardous Area Boxes To Assemble Special Control Stations
IGB-WM Features: Simply attaches to any wall-(screws not included). Removable plastic cover. Accommodates #6 to #2 ground conductors. Accommodates a total of four #14 to #4 bonding conductors.
Inside/outside box mountable. Connector suitable for use with (1) 14/2 to 6/2 NM-B cable or (2) 14/2 to 12/3 NM-B cables in any combination.
Pharmaceutical, Chemical, Food Processing, Pulp/Paper and Nuclear Industries
Protrudes through a hole in a juction box wall to accept a female fitting ouitside the box
Provides Bonding and Conductor Protection with Connectors
Railway Vehicle Construction, Heavy Machine Building Industry and Other Applications with Increased Mechanical Requirements.
Rated for Loads of Up to 500 Pounds/226.80kg with a Safety Factor of Three
Rigid Conduit Systems, Indoors/Outdoors
Rigid compression type coupling used to join Rigid or IMC conduit together.
Roof-mounted supports may be used to support either horizontal or vertical pipe runs.
Signaling Circuits/Remote Control Of Magnetic Motor Starters, Non-Hazardous Areas
Snaps Into a Regular Bushin to Make a UL Listed Insulated Bushing
Splices and Taps, Multi-Device Control Stations, Housing Apparatus, Instruments, Electrical Equipment
Suitable for Use In Hazardous Locations Where General Purpose Equipment is Specifically Permitted by NEC 501-4(B).
Suitable for Use In Hazardous Locations Where General Purpose Equipment is Specifically Permitted by The NEC; Class I, Div. 2; Class II, Div. 1 & 2, NEC 501-4(B); 502-4(A)(B); 503-3(A)(B).
Support attachment of boxes in drywall, paneling, etc. where there is no means of attaching the box to a mounting structure
Threaded Heavy Wall Conduit
Threaded couplings are used to connect lengths of rigid metal conduit and associated elbows together
To Close Threaded Conduit Hubs
To Connect and Effectively Bond Threaded Rigid Metal Conduit/Intermediate Metal Conduit to a Box or Enclosure, or to Couple Ends of Threaded Conduit
To Positively Bond Conduit to Box or Enclosure
To support service entrance cable prior to entrance
To support switch box in wallboard, installed in pairs.
Use with EMT, Rigid Conduit or CU water pipe.
Use with EMT, Rigid Conduit, or CU water pipe.
Used at the end of conduits where no connectors with threads are necessary
Used for capping EMT, rigid or IMC conduit, and most bushings.
Used for converting ordinary bushings and connectors to code approved insulating bushings and connectors without disturbing wiring.
Used inside or outside of an enclosure or panel board in conjunction with a Rigid Metallic Conduit with 3-equipment bonding terminations. Meets the requirement for Intersystem Bonding. Patented
Used to connect non-metallic cable to box or enclosure, locknut not required.
Used to join lengths of threaded rigid or IMC conduit.
Used to join two lengths of threaded rigid or IMC conduit.
Used to make transition from Rigid Metallic Conduit and IMC to EMT in wet and dry locations.
Used to plug knockouts on enclosures to prevent moisture, dust and debris from entering
Used to support FS box, outdoor lighting fixture, or similar devices, per NEC article 370-23.
VMV Series HID Luminaires
holding terminated cable
in a Wide Range of Applications Where it is Important that the Cable Protection System Offers a High Grade of Sealing and Safety
Explosionproof, Dust-Ignitionproof, Raintight
Weatherproof, Watertight, Raintight
304 Stainless Steel
Ball burnished, mirror smooth
Electrogalvanized With Aluminum Acrylic Painted
304 Stainless Steel
316 Stainless Steel
6061-T6 Extruded Aluminum Alloy and Stainless Steel Hardware
NEC/CEC; Class I, Division 1 & 2, Groups A, B, C, D
UL (CANADA AND US)
UL 1203, CSA C22.2
UL 1203, CUL/CSA C22.2
UL 514B, CUL, CSA C22.2
UL 6, CSA C22.2 45.1, ANSI C 80.1
UL 886, CSA C22.2
UL E13938, CSA
UL E16592, CSA
UL E23018, CSA
UL E28720, CSA
UL E3060, CSA
UL E34438, CSA
UL Listed, CSA Certified
UL Standard 886;CSA Standard: C22.2 No.18;National Electric Code/CEC - 1-1/4" through 4" Class I, Division 1 & 2, Groups B, C, D Class II, Division 1, Groups E, F, G Class II, Division 2, Groups F, G Class III
UL Standard: 514B CSA Standard C22.2 No. 18.4
UL and CSA
cULus Listed Raceway: File E4376 Guide RJBT. Fittings: File E41751 Guide RJPR. Base & Blank Cover: Meets Article 386 of NEC. Meets Section 12-600 of CEC.
(1) Duplex Receptacle
Accessory - Adapter
B18-SBT-Z Box/Multiple Conduit Hanger with Rod/Wire Clip
"2.1IN Length X 2.504IN Height, 1/2IN Knockout, 10
12 Thread Pitch
13 trade sizes from 1/2" through 6" - 2 mil green urethane interior coating
40 mil gray PVC exterior coating - 2 mil green urethane interior coating - 12 trade sizes from 1/2" through 6". - Sealing sleeves on all conduit openings - Molded PVC gasket seals fitting
AWG KCM Wire Capacity
AWG Wire Capacity #4 - 14
Ability to install quickly with low torque effort
Accommodates 1/2 in. through 4 in. EMT or rigid conduit.
Adapt an Outlet Hole to The Next Larger Size of Conduit. Rough Ends of Conduit Carefully Covered by Built-In Bushing.
Assembly features bronze ground clamps and copper bonding strip
BRACKET,MOUNTING,LOW VOLTDBL GANG PLATE
Bright orange color clearly signifies a low-voltage installation
Cable Range - .312-1.125 IN
Captive Triple-Lead Quick-Release Hex Head Stainless Steel Bolts
Concrete Tight, when Taped
Conduit/Cable Size: upto 1 IN, Conduit/Cable Clip Type: Push-In, Conduit/Cable Quantity: (1) Cable or Conduit, Finish: Pre-galvanized
Diameter : 5.000 IN
Especially Suited for Use with Flexible Metallic Conduit
Finish: Plain, Lock - A, Polypropylene, Used On: Rigid Conduit/IMC
Fits any flange, tapered or straight, up to 5/8 in. thick
Flame Resistance UL 94, Weight 0.8 Lb per 100
For Service Entrance
HID AND LED STANCHION MOUNT
Hub Size: 1 IN
Hub Size: 1/2 IN
Hub Size: 3/4 IN
Ideal for Cramped Locations or Tight Corners Where Large Radius Conduit Elbows Will Not Fit or Would Appear Unworkmanlike.
Ideal for Entering Enclosure or Conduit Body At Right Angles
Includes Stainless Steel Bolt and Nut for Fast, Easy Installation
Install from outside or inside outlet box or enclosure.
Installed in pairs
Insulating Throat with a Thermoplastic Temperature Rating of 105 Degrees Celcius
Integral snaps provide a secure mount-preventing the ENT from pulling out - but also allow the stub to easily be removed.
MULTI-FUNCTION CLIP,CONDUIT FLNG PLN/THD ROD
Made In USA
Made and Melted in the United States, Electro-plated OD and ID
Maximum Jaw Capacity:1-3/4 IN, Clamp Type - Conduit to Beam
Meets Coast Guard CG293
Mounting screws not provided
Must be used with a locknut
NPSM Threads ROHS Compliant
Non-metallic couplings, adapters and plugs will not rust or corrode.
Operating Force 25 Lb, Raintight, With Pushbutton
Pipe Mount, Pipe Size: 2 IN
Plastic Pre-Kuts will outlast any wood or foam sleeper.
Plated Steel Bracket Hole Size (4) 1.125 IN, (3) 1.75 IN
Precision Cast and Machined Surfaces Permit Safer Wire Pulling.
Produces burr-free cut with no shavings
Provides an economical method of sleeving through
RING,BRIDLE,2 DIA 10-24 THREADED
Raintight /Wet Location Seal
Rugged Material Resists Abrasion, Fits In The End Of Conduit to Shield The Cable from Sharpedges as it is Being Fed Through, Weight : 0.080 Lb, Conduit Size: 3 to 6 IN
Schedule : 40/80
Shoulders on Body of 1/2 In. Size are Hex-Shaped to Provide Positive Holding for Standard Installation Tools.
Sold in pairs, two required per box
Tapered threads (NPT) and furnished plastic K.O. seal provide "raintight" resistance.
The Integral Insulation of the Insulated Elbow is a Guarantee that the Bushing of Every Fitting Will Be Smooth
Thermoplastic Insulating Throat with Rating up to 105 Degree Celcius
Thread Size : 3/4 IN
Tough, corrosion resistant surface. Stainless steel offers durable protection in laboratories, hospitals or food processing areas where corrosive solvents, acid splashes or scalding is a concern.
Trade Size: 1 IN, Size: 1.562 IN Height X 1.812 IN Dia., Installation: Threaded Male/Female, Throat Type: Non Insulated, For Use With IMC Conduit
Trade Size: 1-1/4 IN, Size: 0.875 IN Height X 4.000 IN Dia., Finish: Zinc Plated, For Use With IMC Conduit
Trade Size: 1-1/4 IN, Size: 1.660 IN Dia. X 0.625 IN Height
Trade Size: 1/2 IN, Size: 0.840 IN Dia. X 0.531 IN Height
Trade Size: 1/2 IN, Size: 1.250 IN Height X 1.312 IN Dia., Installation: Threaded Male/Female, For Use With IMC Conduit
Trade Size: 2 IN, Model: PPC
Trade Size: 2 IN, Size: 2.562 IN Height X 3.093 IN Dia., Installation: Threaded Male/Female, Throat Type: Non Insulated, For Use With IMC Conduit
Trade Size: 2.5 IN, Model: PPC
Trade Size: 21/32 IN, Knockout Size: 1/2 IN, Size: 1.000 IN Height
Trade Size: 3/4 IN
Trade Size: 3/4 IN, Model: PPC
Trade Size: 3/4 IN, Size: 1.056 IN Dia. X 0.531 IN Height
Trade Size: 4 IN, Model: PPC
US Made Steel
Use Range: 0.630 - 1.180 IN, Ultimate Tensile: Original 1400 psi, Ultimate Elongation: Original 750 PCT, Die C Tear: Original 150 pli, Fungus Resistance: No Growth 28 Days Exposure, Moisture Absorption: 7 Days at 90 DEG C In H2O 1.8% Weight Gain
Use Range: 1.020 - 1.940 IN, Ultimate Tensile: Original 1400 psi, Ultimate Elongation: Original 750 PCT, Die C Tear: Original 150 pli, Fungus Resistance: No Growth 28 Days Exposure, Moisture Absorption: 7 Days at 90 DEG C In H2O 1.8% Weight Gain
WEIGHT 13 LB PER 100
Wall Thickness 1/4 In, NEMA 3/4/5, Class II Div I Group E F G, Class III Enclosure
Wall Thickness 3/8 In, NEMA 3/4/5, Class II Div I Group E F G, Class III Enclosure
Weight 41 Lb per 100
Weight 50 Lb per 100
Weight 57 Lb per 100
Weight 60 Lb per 100
Will Combine with Any Fitting Having a Male Thread. Male Thread of Panel Connector Extension is 1 In. Long.
With Cover, Cover Opening Diameter 3 In
With Drain, Vertical Position
Zinc Electro-Plated Finish
clear anodize finish
ideal to use when ordering the MB or MBS termination mounting brackets
plugs are wider than size listed to ensure secure connection in enclosure